General
EFI VUTEk Q3h X or XP
Driving the EFI VUTEk Q3h Connection: Click on the icon with the two round arrows, this will open the settings dialog which allows you to enter the IP address of the JMF Server or Q3h/EFI Connector. This is the IP address of the Asani RIP which hosts ...
Summa Twin X
Summa's Twin X mode is a workflow designed to enhance cutting efficiency by integrating Summa roll cutters with F Series flatbed cutters. This integration allows both machines to process the same cutting files and registration marks, optimizing ...
Continuous printing on Epson SC-R5000
There is a method to print "continuously" on the Epson SC-R5000. This means that there will be a smaller gap between the jobs and the printers cool down/warm up sequence will be skipped. The prerequisites for this are as follows: 1. Turn off job ...
SwissQprint Nyala-4: 3 and 5 layer printing - driver settings
Below is the layering in the driver setup to print 3 and 5 layers for the Nyala. To set up the File in Layout: Double sided needs to be enabled: more info on Layout setup for multi layering A. 3 Layer with same image Front and Back Layering = Color / ...
Summa set-up for Barcode reading
The steps below describe how to set up the Summa so that the cut jobs in the RIP are picked up automatically by reading the barcode. File preparation - Layout: Create a print and Cut file using e.g. Summa S Class 2 160 D/T - Select the Summa S Class ...
EFI Vutek Fabrivu or EFI Reggiani installation.
When connecting to theEFI Vutek Fabrivu or EFI Reggiani , there is a folder on the D drive located on the printer controller, which contains three subfolders: "jobs_to_prepare" "jobs_errored" and "print_parameters" Upon connecting to this folder, the ...
Canon Colorado: FLXfinish support
FLXfinish option for the Canon Colorado series enables the combination of matte and gloss finish in 1 job using 1 varnish channel. The effect is created by changing the UV settings. FLXfinish is addressed like a separate ink channel, named Gloss. ...
Canon Colorado
Margin Settings Media Handling Sharing Medias between Colorados Margin Settings Canon Colorado Printers The Canon Colorado offers flexibility with margins through its Print Feed Correction feature. In the RIP driver, you can select from four margin ...
PrintBridge for Hosonsoft
The purpose of Printbridge is to allow print job submission for automatic printing through TCP/IP. Alternatively, there is a folder output option, where the jobs are then opened in the Hosonsoft software for job submission. The Hosonsoft controller ...
SwissQprint driver features using PrintAgent
From V6.6 onwards the SwissQprint Amber series printers uses the PrintAgent service to retrieve job status tracking and job information from the printer to the RIP. More info re PrintAgent, the installer and how to install it can be found here. The ...
Epson SC-S80600 Layering
This article explains the layering options in the Epson SC-S80600 driver. Inkset: First of all, in order to be able to print in multiple layers you need to select a layering inkset: 1. Color = Color only 2. Color + White = Color & White in one layer ...
How to Set Up a Vutek Printer and use the Layered Printing with Specialty Inks
Connecting VUTEk printers usually run a LINUX version on their DFE with a folder \INCOMING\ already shared (if no share is yet created, check the DURST install instructions for sharing folders on a UNIX system or check with local IT; more info might ...
Summa S Class 2 Extended load
The Summa S Class 2 series cutters have an 'Extended Load' function. This function makes it possible to define the limits of the Y axis so that the cutter can cut outside the pinch rollers. The media needs to be loaded before this function can be ...
HP Job status reporting - settings in IPS
When enabling the Job Status tracking for HP Latex series, following setting on the IPS need to be enabled. The communication for copy count and ink status is reported back to the RIP via JMF notifications. In case the jobs are removed from queue, it ...
Roland Cutter Setting adjustment
This article provides a quick guide on how to adjust the settings on your Roland cutter to ensure that the coordinate system works optimally. By default, the home position is set on the left side of the cutter. However, for better alignment with the ...
Kornit DTG set-up
Kornit DTG printers uses a dynamic configuration system based on KST files. Those files define the resolutions, media properties and all handling settings that are available in the DFE of the printer. At the printer a the PrintAgent needs to be ...
HP Latex R1000/R2000 Job Flow
The HP Latex R1000 and R2000 flatbed printers have their own digital front end internal print server (IPS). PrintFactory will output ripped files to the output folder specified in the RIP device options. The PrintFactory ripped files can be ...
swissQprint Karibu – Configuration setup
When installing the swissQprint karibu driver in the RIP, the specific content for this driver (e.g. ink channels, print modes,..) needs to be obtained from the configuration file created on the Lory Front-End of the printer. To find the .sqpe file ...
Summa S2 OPOS-Cam
The Summa S2 OPOS-CAM model requires the use of the Summa Cutter Control software, it cannot be driven directly from the PrintFactory RIP unlike the OPOS sensor models. This is because it has a camera instead of a sensor to read the marks and ...
DYSS Ground Table Set-up
The DYSS driver in PrintFactory assumes a specific tool set-up. When the current ground table in the Kasemake software (which drives the DYSS) is not matching the defined set-up the operator needs to remap the tools. For the convenience of the ...
Summa Cutter OPOS Barcode
What? PrintFactory supports the use of the Summa OPOS Barcode. There’s a built-in Summa Barcode server embedded in our software which is in use if the cutter is connected directly to the RIP by USB or TCP/IP. When a print & cut job is created (See ...
Inca Installation
The installation of an Inca printer consists of 2 important steps: Copy the currently used IncaDeviceDetails .txt into the RIP installation Install and set-up PrintAgent IncaDeviceDetails The IncaDeviceDetails.txt is used to define the print modes ...
HandTop
Below are the configuration and set-up instruction for HandTop printers. Workflow There are 2 ways of connecting the HandTop printer. The first way is the send print files to the HandTop TOPJet application, where you can pickup the file and get it ...
PrintFactory Zund Cut Center integration
PrintFactory Zund Cut Center(ZCC) drivers have direct bidirectional communication with Zund Cut Center, the software installed on Zund digital front ends. We have made it easy to integrate your Zund cutter into the PrintFactory workflow thus reducing ...
Zund Cut Center RIP Queues
What? From V6.4.0 onwards it is now possible to make Cut Only RIP Queues for Zund Cut Center (ZCC) drivers. This means that you can submit cut files straight into a hotfolder & the file will be processed and sent directly to the ZCC Job Queue with ...
Océ Colorado 1640: tension bar settings
This document describes how the tension bar settings are defined and what changes are allowed. Tension bar settings in Media list The media settings are accessible when double clicking a media from the media list in Calibrator. Every media belongs to ...
Océ Colorado 1640: managing media and print mode settings
Océ have decided upon an architecture where the print and media settings are stored in the printer profile. Consequently, any changes to these settings require changing the pmm. This document describes how media and print settings are changed once ...
Océ Colorado PMM handling
The Océ Colorado Printer has new media handling functionalities not previously seen. Therefore we have adapted the Calibrator to support this new workflow. This FAQ explains how this is implemented using VISU profile creation. MX is not compatible ...